Toyota Camry

1996-2001 of release

Repair and car operation


Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
   - 3.3. A partition of engines
      3.3.1.2. 6-cylinder двухрядные engines
      3.3.2. Engine major repairs – broad-brush observations
      3.3.3. Diagnostics of the engine with the help вакууметра
      3.3.4. Engine major repairs – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. An engine partition
      3.3.8. A head of cylinders and valves
      3.3.9. The balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. A cranked shaft
      3.3.12. The block of cylinders
      3.3.13. Хонингование cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. A back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is more likely live, than it is dead …
      3.3.22. The analysis дымности an exhaust
      3.3.23. A gear belt for a mechanism drive timing
      3.3.24. Occurrence in deposit oil
      3.3.25. An engine overheat
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4

3.3.6. Removal and engine installation

Removal

PERFORMANCE ORDER
1. Pit pressure in fuel system.
2. Disconnect a wire of the minus plug of the accumulator.
3. Remove the accumulator and an accumulator arm.
4. Remove an engine cowl.
5. Remove the air filter.
6. Lift and fix the car. Merge cooling liquid and engine oil. Remove приводные belts.

7. Mark both ends disconnect vacuum hoses, hoses of a cooling liquid and final gases. Disconnect wires and fuel tubes. To mark wires use изоляционную a tape.
8. Remove a broad tank of system of cooling and a tank windscreen.
9. Remove radiator fans, a casing of fans and a radiator.
10. Disconnect heater hoses.
11. Disconnect the fuel tubes connecting the engine with a body.
12. Disconnect from the engine a rope throttle заслонки, a rope of the throttle valve of a transmission and a rope of the gauge of a speedometer.
13. Disconnect holders of a plait of wires of the engine.
14. Unscrew assembly bolts of the pump of system of strengthening of a wheel. Whenever possible shift the pump aside without disconnecting from it hoses. If necessary remove the pump.

15. Remove the compressor of the air conditioner and shift it aside. Do not disconnect hoses from the compressor.
16. Disconnect an exhaust pipe () from a collector (ов).

17. In four-cylinder engines remove the oil filter, disconnect hoses from an oil radiator and remove an oil radiator (arrow).
18. Fix a chain on hooks intended for a raising of the engine and connect a chain to the lift.

19. Remove a leading axis () from outside passenger sitting, unscrew a through bolt of a support of the engine () and remove a back arm of the engine ().

20. Unscrew a bolt, крепящий a forward support of the engine to a body () if you remove the engine together with a transmission, remove the engine shock-absorber ().
21. In models with an automatic transmission remove the dustproof screen of the hydrotransformer, remove clamps of the hydrotransformer and slightly press the hydrotransformer into a transmission casing.
22. If you remove only the engine, unscrew bolts and disconnect a transmission.
23. Check up that nothing disturbed to engine removal.
24. Establish a jack under a transmission. Unscrew bolts from engine support.

25. Slowly lift the engine on the lift (in drawing the 4-cylinder engine together with a transmission is shown).
26. Lower the engine on specially equipped rack or on a workshop floor.

Installation

PERFORMANCE ORDER
1. In engines with a mechanical transmission, examine elements of coupling and grease press the bearing.
2. In engines with an automatic transmission, examine a lining and the plug of the hydrotransformer and grease its forward part.
3. Establish the engine upside-down removals.