Toyota Camry

1996-2001 of release

Repair and car operation

Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
   - 3.3. A partition of engines
      3.3.1.2. 6-cylinder двухрядные engines
      3.3.2. Engine major repairs – broad-brush observations
      3.3.3. Diagnostics of the engine with the help вакууметра
      3.3.4. Engine major repairs – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. An engine partition
      3.3.8. A head of cylinders and valves
      3.3.9. The balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. A cranked shaft
      3.3.12. The block of cylinders
      3.3.13. Хонингование cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. A back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is more likely live, than it is dead …
      3.3.22. The analysis дымности an exhaust
      3.3.23. A gear belt for a mechanism drive timing
      3.3.24. Occurrence in deposit oil
      3.3.25. An engine overheat
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment

3.3.17. Radical bearings of a cranked shaft

THE GENERAL DATA

Sequence of a tightening of bolts of covers of radical bearings (4-cylinder engines)

Sequence of a tightening of bolts of the block of covers of radical bearings (6-cylinder engines)

Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines)

Check of a lubricant backlash of radical bearings

PERFORMANCE ORDER

1. Establish new loose leaves of radical bearings.

2. Clear a cranked shaft, bearings and lubricant apertures, then accurately establish a cranked shaft on bearings.

3. Put a plastic piece on each of radical bearings along a shaft axis.

4. Establish covers of radical bearings, trying not to shift plastic arts. Tighten fixing bolts of covers till the demanded moment of an inhaling in the specified sequence (fig. Sequence of a tightening of bolts of covers of radical bearings (4-cylinder engines), fig. Sequence of a tightening of bolts of the block of covers of radical bearings (6-cylinder engines), fig. Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines) see . Do not turn a cranked shaft.

5. In 6-cylinder engines after you have tightened bolts till the demanded moment of an inhaling of the first step, hold on on a turn quarter.

6. Unscrew bolts, and accurately remove covers.

7. Compare width of the crushed film to a special scale for definition of size of a lubricant backlash.

8. If the backlash size does not correspond to technical requirements, establish loose leaves of other size. If necessary bearings can be ground.

9. Carefully remove traces of a film from a shaft and bearings.

Definitive installation of a cranked shaft

PERFORMANCE ORDER

1. Accurately remove a cranked shaft.

2. Clear a surface of loose leaves and grease with their greasing or engine oil. Check up, that bearings of a cranked shaft were pure and establish a cranked shaft into place. Grease and establish the bottom loose leaves. Establish persistent half rings.

3. In 4-cylinder engines establish persistent half rings in a cover of the third bearing, and in 6-cylinder – in a cover of the second bearing.

4. Establish covers of radical bearings. Arrows of covers should be directed towards a forward part of the engine. Insert and tighten bolts of covers of all radical bearings till the demanded moment of an inhaling in the specified sequence (fig. Sequence of a tightening of bolts of covers of radical bearings (4-cylinder engines), fig. Sequence of a tightening of bolts of the block of covers of radical bearings (6-cylinder engines), fig. Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines) see .

5. Do not forget to establish new sealing washers on lateral шестигранные bolts.

6. Turn a cranked shaft a hand some times and check up ease of a course.

7. Check up axial люфт a cranked shaft and establish a back epiploon.