Toyota Camry

1996-2001 of release

Repair and car operation


Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
   - 3.3. A partition of engines
      3.3.1.2. 6-cylinder двухрядные engines
      3.3.2. Engine major repairs – broad-brush observations
      3.3.3. Diagnostics of the engine with the help вакууметра
      3.3.4. Engine major repairs – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. An engine partition
      3.3.8. A head of cylinders and valves
      3.3.9. The balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. A cranked shaft
      3.3.12. The block of cylinders
      3.3.13. Хонингование cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. A back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is more likely live, than it is dead …
      3.3.22. The analysis дымности an exhaust
      3.3.23. A gear belt for a mechanism drive timing
      3.3.24. Occurrence in deposit oil
      3.3.25. An engine overheat
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4

3.3.12. The block of cylinders

Cleaning

PERFORMANCE ORDER
1. Turn заглушки in apertures, having struck a stupid core побоковой parts of everyone заглушки.
2. Take plastic заглушки flat-nose pliers.

3. In the 6-cylinder engine instead of plastic заглушек metal plates are established.
4. By means of a plastic scraper clean off all traces of hermetic from a joined surface of the block of cylinders.
5. Unscrew or drill заглушки oil channels from the block of cylinders. Use new заглушки during assemblage.
6. If too dirty, it it is necessary to clean the block in a specialised workshop.
7. Clean and wash out oil apertures and channels warm water. Dry apertures and channels, having blown their compressed air. Grease the block with anticorrosive oil.
8. Clean carvings of apertures in the block by means of taps of the necessary size. Clean bolts of a head of cylinders and bolts of radical bearings.
9. Establish covers of radical bearings and twist bolts.

10. By means of the special tool hammer new, greased with hermetic, заглушки into block apertures.
11. Put hermetic on заглушки oil channels and twist them in the block.

Check

PERFORMANCE ORDER
1. Examine the block on presence of cracks and corrosion or rust traces. Examine carvings of apertures of the block. At detection of defects, it is necessary to repair or replace the block whenever possible.
2. Examine cylinders and check up them on конусность and ovality.
3. Measure diameter of each cylinder of perpendicularly central line () and in parallel central line () (1 – the central line of the engine).
4. Measure diameter of the cylinder by means of a telescopic measuring instrument.

5. Measure length of a telescopic measuring instrument by means of a micrometer.
6. Measure diameter of each cylinder in the top average and bottom its parts, perpendicularly axes of a cranked shaft.
7. Конусность the cylinder it is calculated as a difference between top and bottom in diameters. Ovality – as a difference between parallel and perpendicular gaugings.
8. If the received results do not coincide with technical requirements, cylinders are necessary for processing in a specialised workshop.

9. By means of a ruler and probeов check up, whether the surface of the block joined to a head is deformed.
10. Check up deterioration of pistons and cylinders with the help probeов. At a finding of deterioration or damages at block survey, address to experts.