| 1. Turn away a stopper of a nutritious tank of brakes. |
| 2. Release nuts of wheels, lift the car (a forward or back part) and establish on supports. |
| 3. Remove wheels. |
| 4. Attentively check up a disk condition (subsection 10.6 see.). In need of grinding or replacement remove a disk and Pads. |
|
5. Drown pistons in cylinders to establish new Pads. If necessary use a clamp. On a measure утапливания the piston liquid level in a tank will raise. Remove surplus of a liquid, having sucked away a syringe. |
|
6. Before work clear brake details special structure. |
|
7. Turn away the bolts specified by the top and bottom arrows (a bolt of the union of a hose to turn on only if the support acts in film from the car). |
|
8. Remove a support. |
|
9. Fix a support a wire, without supposing sagging on a hose. |
|
10. Remove the top antinoise spring колодок (on 4-cylinder models). |
|
11. Remove the bottom antinoise spring колодок (on 4-cylinder models).
|
|
|
| 12. Remove external and internal antinoise plates with external Pads. |
|
13. Remove external колодку. |
|
|
| 14. Remove external and internal antinoise plates with internal Pads. |
|
15. Remove internal колодку. |
|
16. Remove clamps колодок, check up their condition and if necessary replace (clamps should be latched in nests support arms, at detection of deformations or easings of landing clamps replace). |
|
17. Hook and remove the index of deterioration with internal Pads and rearrange the index on new колодку. At detection of damages the indicator replace. |
|
18. Establish a clamp Pads, new internal колодку and antinoise plates. Track that ears of antinoise plates have come into grooves on clamps колодок. |
|
19. Establish a clamp Pads, new external колодку and antinoise plates. |
|
20. Establish the top and bottom antinoise springs колодок (on 4-cylinder models), track, that springs have entered into gearing with колодками. |
|
21. Get the top and bottom fingers Pads and clear them (replace the damaged rubber cover, having hooked a fillet on the metal plug). |
|
22. Then grease a finger with refractory greasing and establish into place. |
|
23. Establish a support and tighten bolts with the set moment. |
| 24. Before replacement of back disk brakes clear brake details. |
|
25. Turn away a bolt of fastening of a support (it is specified by the bottom arrow), the bolt of the union of a hose (the top arrow) to turn on only if the support acts in film from the car. |
|
26. Cast away a support and fix. |
|
|
| 27. Remove an external and internal antinoise plate with external Pads. |
|
28. Remove external колодку. |
|
|
| 29. Remove an external and internal antinoise plate with internal Pads. |
|
30. Remove internal колодку. |
|
31. Remove clamps колодок, check up their condition and if necessary replace (clamps should be latched in nests of an arm of a support, at detection of deformations or easings of landing clamps replace). |
|
32. Establish a clamp Pads, new internal колодку and antinoise plates. Track that antinoise plates have entered into gearing with колодками and with each other. |
|
33. Establish clamps Pads, new external колодку and antinoise plates. Track that antinoise plates have entered into gearing with external колодкой with each other. |
|
34. Lower a support, having put on it on new Pads. Tighten a bolt with the set moment. |
|
35. Upon termination of assemblage some times press a brake pedal to reduce Pads with a disk. Check up liquid level, if necessary add. Check up work of brakes.
|
