Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
- 10. Brake system
10.2. Technical characteristics
10.3. ABS-system
10.4. Колодки disk brakes
10.5. A brake support
10.6. A brake disk
10.7. Колодки drum-type brakes
10.8. The wheel cylinder of brakes
10.9. The main cylinder of brakes
10.10. Hoses and hydrodrive tubes
10.11. Removal of air from a hydrodrive of brakes
10.12. The vacuum amplifier of brakes
10.13. Колодки a lay brake of back disk brakes
10.14. A lay brake
10.15. Cables of a lay brake
10.16. The switch of a signal of braking
10.17. ABS: a natural choice
10.18. Malfunctions of brake system
+ 11. A body
+ 12. An electric equipment
|
The amplifier of brakes
|
1. The main cylinder
2. A hose
3. A lining
4. A plug axis
5. A plug
|
6. Шплинт
7. The vacuum amplifier
8. A lining
9. A splitter on ABS-system brakes |
Check of work of the vacuum amplifier
| PERFORMANCE ORDER |
| 1. Press some times a brake pedal on the idle engine. The pedal course by each pressing should not to vary. |
| 2. Press a pedal and start the engine, – on the serviceable amplifier the brake pedal should be displaced a little forward. |
|
Tightness check
| PERFORMANCE ORDER |
| 1. Start the engine, later 1–2 mines stop. Slowly press a pedal some times. On the serviceable amplifier the course of a pedal with each pressing should decrease gradually. |
| 2. Start the engine and press a pedal. Keeping a pedal pressed, stop the engine, – during 30 сек after a stop pedal position should not to vary. |
|
If the amplifier is faulty, he will lie down to replacement, unit repair is impossible even in the conditions of car-care centre.
Removal
| PERFORMANCE ORDER |
| 1. Remove the main cylinder (subsection 10.9 see.). |
| 2. Remove a tank for catching of steams of gasoline (subsection 7.2.20 see.). |
| 3. Remove the air filter (subsection 6.11 see.). |
| 4. Cautiously disconnect from the amplifier a vacuum hose. |
| 5. Working in salon, remove a casing of a steering column (subsection 11.24 see.). |
| 6. Having illuminated a lantern, find a plug of a pusher of the vacuum amplifier in a fastening place on a brake pedal. Расшплинтуйте also get a plug axis. |
| 7. Turn away four nuts of fastening of the amplifier of brakes to a partition of a motor compartment. |
| 8. Submit the amplifier and remove when hairpins leave apertures in a partition. |
|
Installation
Installation is made in sequence, return to removal.
If the new unit adjust a backlash between a pusher of the main cylinder of a brake and an amplifier pusher is established. For this purpose execute the following.
| PERFORMANCE ORDER |
|
1. Between pushers of the vacuum amplifier and the main cylinder of a backlash should not be. If a backlash nonzero the course of a pedal of a brake increases. If on the contrary, the amplifier pusher rests against a cylinder pusher wheels can not растормаживаться. |
|
2. Measure выступание a pusher over a lining on the amplifier case. It is the size And. |
|
3. Measure distance from an end face of the main cylinder to a flange plane. It is the size of Century |
|
4. Measure distance from an end face of the main cylinder to the bottom piston dredging. It is the size With. |
| 6. The backlash between a pusher and the piston is equal (In–) – And and should be equal 0. If necessary adjust выступание a pusher of the vacuum amplifier. |
|
7. For pusher adjustment compress a pusher for a neck with накаткой and rotating a pusher tip establish such выступание And that the backlash was equal In – S.Snova check up a backlash. If necessary repeat adjustment. |
| 8. Upon termination of establish the main cylinder, attach tubes, adjust height of a pedal and a free wheeling. Remove air from a hydrodrive. |
|
|
|
