Toyota Camry

1996-2001 of release

Repair and car operation


Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS-system
   10.4. Колодки disk brakes
   10.5. A brake support
   10.6. A brake disk
   10.7. Колодки drum-type brakes
   10.8. The wheel cylinder of brakes
   10.9. The main cylinder of brakes
   10.10. Hoses and hydrodrive tubes
   10.11. Removal of air from a hydrodrive of brakes
   10.12. The vacuum amplifier of brakes
   10.13. Колодки a lay brake of back disk brakes
   10.14. A lay brake
   10.15. Cables of a lay brake
   10.16. The switch of a signal of braking
   10.17. ABS: a natural choice
   10.18. Malfunctions of brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4 escort magic

10.15. Cables of a lay brake
THE GENERAL DATA

Details тросового a drive of a lay brake
1. A cover лючка
2. An arm (cars with separate seats)
3. A cable of lay brake N4
 4. The intermediate lever
5. A cable of lay brake N1
6. The plug
7. Intensifying section

Details тросового a drive from a pedal to the intermediate lever
1. A cable отпускания a lay brake
2. A pedal overlay
3. A cable of lay brake N1
4. Скоба
5. An axis
6. The switch of a signal of a lay brake

Replacement

THE CABLE CONNECTING LEVELING PLANCK WITH LAY BRAKES OF BACK WHEELS

PERFORMANCE ORDER
1. Lift a back part of the car.
2. Release a lay brake and remove a drum (disk).
3. On а/м with back drum-type brakes remove Pads and disconnect a cable from the drive lever Pads. On а/м, equipped with back disk brakes, remove Pads a lay brake and disconnect the drive lever Pads.
4. Turn away bolts of a tip of a cable of a lay brake on a brake board.
5. Turn away a bolt of fastening of an arm of a cover of a cable. The arm of a cover of a cable is located in a forward part of a bar of a back suspension bracket (on a part of cars the arm arrangement can differ a little).
6. Remove average section of an exhaust pipe (or приопустите it) to provide access to cables.
7. Turn away a bolt of fastening of a collar of a forward tip of a cover of a cable and deduce a tip from a collar.
8. Turn a cable so that the cable tip left gearing with a lath of the equalizer and unhook a cable.
9. Installation is carried out upside-down.
10. Adjust a cable.

THE CABLE CONNECTING THE INTERMEDIATE LEVER WITH THE LEVELING LATH

PERFORMANCE ORDER
1. Remove the central section.
2. Release the lever of a brake and turn away a counternut and adjusting nuts. Disconnect a cable from the lever.
3. Working under the car, submit a cable back, turn on 90 ° and extend a cable, having passed through an aperture in a floor.
4. Installation is carried out upside-down. Grease rubbing parts of a tip of a cable in a levelling lath. Adjust a cable.

THE CABLE CONNECTING THE INTERMEDIATE LEVER WITH THE PEDAL (ONLY FOR MODELS AVALON)

PERFORMANCE ORDER
1. Remove a forward seat.
2. On а/м with a seat скамеечного type remove intensifying section, on а/м with separate seats remove the central section.
3. Disconnect a cable from the intermediate lever.
4. Remove the knee buffer of safety (subsection 11.23 see.).
5. Disconnect the switch of a signal of a lay brake.
6. Расшплинтуйте also get a pedal axis, disconnect from a pedal a cable.
7. Installation is carried out upside-down.