Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
- 9. A running gear
- 9.1.2. Technical characteristics
9.1.3. The stabilizer of cross-section stability of a forward suspension bracket
9.1.4. A rack of a forward suspension bracket
9.1.5. A rack and a suspension bracket spring
9.1.6. The suspension bracket lever
9.1.7. Spherical support
9.1.8. A rotary fist and a nave
9.1.9. A nave and the bearing of a forward wheel
9.1.10. The stabilizer and plugs of the stabilizer of a back suspension bracket
9.1.11. A rack of a back suspension bracket
9.1.12. A longitudinal bar
9.1.13. Levers of a back suspension bracket
9.1.14. A nave and the bearing of a back wheel
9.1.15. An arm of a back suspension bracket
9.1.16. Corners of installation of wheels
+ 9.2. A steering
+ 9.3. Semiaxes
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment
|
Replacement
PERFORMANCE ORDER |
1. Lift the car and remove a wheel.
The prevention If the spherical support leaves a stripper захватного type before wheel dismantle release a nut of a nave of a wheel (semiaxis).
|
|
REMOVAL OF THE SUPPORT BY MEANS OF SLIDING ВИЛЬЧАТОГО THE STRIPPER
The prevention Procedure considered more low provides the fastest removal of a spherical support, however, thus the cover of a finger of a support for certain will be damaged. If the cover has to be kept, be guided by the description in point Removal of a support from the help захватного a stripper.
PERFORMANCE ORDER |
1. Рашплинтуйте also release a nut of a finger of a spherical support, a nut not completely not to turn on. |
2. Выпрессуйте a spherical support from a rotary fist by means of sliding вильчатого a stripper. Grease a cover консистентной with greasing and work cautiously not to tear a cover. Turn away a nut of a finger of a support. |
|
|
3. Turn away a bolt and nuts of fastening of a spherical support to the lever of a suspension bracket and separate a support from the lever. |
4. At assemblage establish a spherical support on a rotary fist and screw a nut, a nut not to tighten. |
5. Establish a support on the lever, turn and tighten nuts and a bolt with the set moment. |
6. Tighten a nut of a finger of a support with the set moment and зашплинтуйте (шплинт replace new). If шплинт does not come into nut grooves slightly tighten a nut before coincidence of the nearest groove with шплинтом. |
7. Establish a wheel and lower the car. |
|
REMOVAL OF THE SUPPORT BY MEANS OF ZAHVATNOGO ВИЛЬЧАТОГО OF THE STRIPPER
PERFORMANCE ORDER |
1. Separate a spherical support from the suspension bracket lever (subsection 9.1.6 see.). |
2. Get полуось from a rotary fist (subsection 9.3.2 see.) also suspend, having fixed a wire. |
3. Рашплинтуйте also release a nut of a finger of a spherical support, a nut not completely not to turn on. |
|
4. Dress захватную a part of a stripper and выпрессуйте a spherical support from a rotary fist. |
5. Turn away a nut of a finger of a spherical support and remove a support. |
6. At assemblage establish a new spherical support on a rotary fist and tighten a nut with the set moment. |
7. Insert полуось into a rotary fist and wrap a nut. Tighten a nut, but not to the full. |
8. Establish a support on the lever and tighten nuts and a bolt with the set moment. |
9. Establish a wheel and lower the car. Wheel nuts tighten with the set moment. |
10. Tighten a nut of a nave with the set moment (subsection 8.3.1 see.), establish a lock washer and шплинт. |
|
|
|