Toyota Camry

1996-2001 of release

Repair and car operation

Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
- 10. Brake system
   10.2. Technical characteristics
   10.3. ABS-system
   10.4. Колодки disk brakes
   10.5. A brake support
   10.6. A brake disk
   10.7. Колодки drum-type brakes
   10.8. The wheel cylinder of brakes
   10.9. The main cylinder of brakes
   10.10. Hoses and hydrodrive tubes
   10.11. Removal of air from a hydrodrive of brakes
   10.12. The vacuum amplifier of brakes
   10.13. Колодки a lay brake of back disk brakes
   10.14. A lay brake
   10.15. Cables of a lay brake
   10.16. The switch of a signal of braking
   10.17. ABS: a natural choice
   10.18. Malfunctions of brake system
+ 11. A body
+ 12. An electric equipment


10.13. Колодки a lay brake of back disk brakes

Details of a lay brake

1. A directing lath
2. A spring
3. Распорка
4. Back колодка
5. A remote lining
6. An axis
7. Returnable springs колодок
8. A support of a back disk brake
9. Заглушка
10. A disk
11. A clamping spring Pads
12. Cups of a clamping spring
13. A spring колодок pulling together
14. A regulator
15. A lobby колодка
16. An axis
17. The drive lever Pads
18. A cutting washer

The prevention

Колодки a lay brake vary only in steam on an axis.

Check and replacement

1. Remove a brake disk (subsection 10.6 see.).
2. Check up a residual thickness of frictional overlays. Колодки than 0,8 mm are subject to replacement, if a thickness of a material less.
3. Remove a nave with bearings (section 9.1.14 see.).
4. Clear brake details special structure.
5. Remove pulling together spring back Pads a lay brake from an axis and unhook a spring from back Pads.
6. Remove pulling together spring of a lobby Pads a lay brake from an axis and unhook a spring from a lobby Pads.
7. Remove a clamping spring back Pads and get an axis.
8. Remove распорку.
9. Remove a clamping spring of a lobby Pads and get an axis.
10. Remove a backlash regulator between колодками and a disk drum (the pulling together spring is behind a regulator and in a picture it is not visible).
11. Get a cutting spring washer from an axis of the lever of a drive Pads a lay brake on back колодке and remove the lever.
12. Grease with a thin layer of refractory greasing a rubbing surface of a board of a brake.
13. Dress a cable on the lever and fix a spring cutting washer.
14. Dress pulling together spring from an underside back Pads and from a lobby underside Pads.
15. Establish a regulator, having brought Pads to each other. The regulator terminations should enter into gearing with колодками.
16. Establish Pads, establish распорку and a spring. The vilchatye terminations распорки should come into grooves колодок.
17. Establish a returnable spring forward and back Pads.
18. Establish a clamping spring back and forward Pads
19. As a result of correct assemblage of a detail settle down as in drawing.
20. Establish a disk of a brake and fix, having screwed 3 nuts of a wheel.
21. Turn out from a disk заглушку. Adjust Pads for what rotating маховичок regulator hairpins dissolve Pads against the stop in a drum (the drum thus should not rotate) and take away, having turned on маховичок a regulator on 8 teeth.
22. Establish a support arm, tighten bolts with the set moment.
23. Establish a wheel.
24. On а/м, equipped with the lever of a lay brake, check up number of clicks of the lever before full braking which should be from 5 to 8. Otherwise adjust.
25. For extra earnings колодок a lay brake arrive as follows. On а/м, equipped with the lever of a lay brake, moving with a speed of 50 km/hour on equal dry highway, include a brake, having made the lever effort 8кГс. On а/м with a pedal of a lay brake, include a brake, having made effort to a pedal 13кГс. Having passed about 0,5 km, release a pedal.
26. Repeat this procedure 2–3 times, allowing to cool down preliminary колодкам.