Toyota Camry

1996-2001 of release

Repair and car operation



Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
- 2. Maintenance service
   2.2. The schedule of servicing Toyota Camry/Avalon
   2.3. Primary and secondary checks
   2.4. Check of level of oil and liquids
   2.5. Check of a condition of tyres and pressure in tyres
   2.6. Check of level of a liquid of system of hydrostrengthening of a steering
   2.7. Check of level of liquid automatic gearbox
   2.8. Replacement of engine oil and the oil filter
   2.9. Survey and replacement of brushes of screen wipers
   2.10. Check, servicing and accumulator gymnastics
   2.11. Check, adjustment of a tension and replacement drive a belt
   2.12. Check and replacement of hoses in an impellent compartment
   2.13. Check of system of cooling
   + 2.14. Shift of wheels
   2.15. Check of brake system
   2.16. Replacement of the air filter
   2.17. Power supply system check
   2.18. Check of level of a liquid of differential (automatic gearbox)
   2.19. Check of level of oil manual transmission
   2.20. Steering and suspension bracket check
   2.21. Check of covers of semiaxes
   2.22. Check of final system
   2.23. Height and a free wheeling of pedals of coupling and a brake
   2.24. Replacement of the fuel filter
   2.25. Replacement of a cooling liquid and washing of system of cooling
   2.26. Check of the system, supervising allocation of steams of fuel
   2.27. Replacement of liquid automatic gearbox
   2.28. Replacement of oil manual transmission
   2.29. Check of fastenings of a body
   2.30. Check and replacement of spark plugs
   2.31. Check and replacement of wires of spark plugs
   2.32. Check and adjustment of backlashes of valves
   2.33. Replacement of a lining of a cover of a jellied mouth of a fuel tank
   2.34. Check and replacement of the valve of ventilation картера
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4 футбол ставка
На сайте http://www.9228416.ru ремонт стиральных машин.

2.32. Check and adjustment of backlashes of valves
THE GENERAL DATA

Backlashes of final valves of the first both third cylinders and backlashes of inlet valves of the first and second cylinders (the four-cylinder engine)
 

Backlashes of valves (the six-cylinder engine)
1. The right head, final valves

2. The right head, inlet valves

3. The left head, inlet valves

4. The left head, final valves

Backlashes of valves of the 4-cylinder engine (remained)
 IN – Inlet valves

 EX – Final valves

Backlashes of valves of the 6-cylinder engine (remained)
 IN – Inlet valves


 EX – Final valves

Backlashes of valves of the 6-cylinder engine (remained) – 2
 IN – Inlet valves


 EX – Final valves

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. In four-cylinder models disconnect wires of spark plugs.
3. In six-cylinder engines merge cooling liquid and remove the air filter. Disconnect wires of spark plugs of a back row of cylinders and remove wires and coils of ignition of candles of a forward number.
4. Unscrew spark plugs.
5. Uncover heads.
6. Establish cylinder N1 piston in position ВМТ at the moment of a compression step.
7. Measure a backlash of each of valves by means of a set probeов.
8. On models with the four-cylinder engine turn a cranked shaft on one complete revolution and combine adjusting marks in a pulley of a cranked shaft. Measure backlashes of the remained valves (fig. Backlashes of valves of the 4-cylinder engine (remained see)).
9. On models with the six-cylinder engine turn a cranked shaft on 2/3 turns (240 degrees) clockwise. Measure backlashes of the specified valves (fig. Backlashes of valves of the 6-cylinder engine (remained see)). Turn a cranked shaft on 2/3 turns and measure backlashes of the remained valves (fig. Backlashes of valves of the 6-cylinder engine (remained) – 2 see).

10. Turn a cranked shaft so that a cam over the valve demanding adjustment, has been lifted upwards.

11. Turn the lift of the valve a cut to a spark plug. Establish the tool and press the lift. Compress the lift the special tool to remove a lining.
12. Remove a lining by means of a small screw-driver or a magnet.
13. Measure a thickness of a lining by means of a micrometer.
14. Calculate a demanded thickness of a new lining under the following formula:
N = T + (A – V)
Т = a thickness of an old washer
A = клапанный a backlash
N = a thickness of a new washer
V = recommended клапанный a backlash.
15. Establish a new lining, and repeatedly check up клапанный a backlash.