Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
- 9. A running gear
- 9.1.2. Technical characteristics
9.1.3. The stabilizer of cross-section stability of a forward suspension bracket
9.1.4. A rack of a forward suspension bracket
9.1.5. A rack and a suspension bracket spring
9.1.6. The suspension bracket lever
9.1.7. Spherical support
9.1.8. A rotary fist and a nave
9.1.9. A nave and the bearing of a forward wheel
9.1.10. The stabilizer and plugs of the stabilizer of a back suspension bracket
9.1.11. A rack of a back suspension bracket
9.1.12. A longitudinal bar
9.1.13. Levers of a back suspension bracket
9.1.14. A nave and the bearing of a back wheel
9.1.15. An arm of a back suspension bracket
9.1.16. Corners of installation of wheels
+ 9.2. A steering
+ 9.3. Semiaxes
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment
|
Details of a rack of a forward suspension bracket (the device of a rack of a back suspension bracket similarly)
1. The top basic cup
2. The bearing
3. The top saddle
4. The spring buffer
5. Top изоляционный a spring casing
6. Bottom изоляционная a spring lining
7. A spring
|
8. The suspension bracket shock-absorber
9. Conducting of the gauge of speed of ABS-system
10. Draught of the stabilizer
11. A brake hose
12. A rack in gathering |
If obvious signs of deterioration or rack or spring damage (подтекание liquids, a corf of springs, external damages, etc.) it is necessary to deal with a question on expediency of dismantling are found out. The rack with the shock-absorber is not subject to repair and varies in gathering. Dismantling
PERFORMANCE ORDER |
1. Remove a rack. Clamp the bottom part of a rack in a vice through wooden linings. |
|
2. Compress a spring by means of the adaptation so that to remove pressure upon the top basic cup of a spring (is checked by rocking of the top plate). |
The prevention At spring removal use the special adaptation for spring compression. The removed compressed spring store in a safe place.
|
|
3. Turn away a nut of a rod of the shock-absorber. |
|
4. Turn away a nut and remove a cup of the top support of a rack. Check up a condition of the bearing of a cup. If the bearing заедает at rotation a cup replace. Check up integrity of a rubber lining of a cup, presence on it of cracks and deterioration signs. If rubber destruction replace a lining is found out. |
|
5. Remove the top saddle of a spring. Check up presence on a saddle of cracks and hardenings. If necessary replace. Remove top изоляционный a spring casing. |
|
6. Cautiously remove the compressed spring. |
7. Remove the rubber buffer. |
8. Check up a condition bottom изоляционной linings, if necessary replace. |
|
Assemblage
PERFORMANCE ORDER |
1. If varies bottom establish it into place so that the ledge on a lining has been turned downwards and has come into deepening on the bottom cup of a rack. |
|
2. Establish a spring so that the termination of last coil has come into deepening on bottom изоляционная to a lining. |
|
3. Establish top изоляционный a casing and a spring saddle, having combined thus лыски on a rod of the shock-absorber with sides of an aperture of a saddle. |
|
4. Combine label OUT of the top saddle of a spring with a label on top изоляционном a casing. |
|
5. At assemblage of a rack of a forward suspension bracket be convinced that the arrow on a saddle is turned outside (1 – outside). |
|
6. At assemblage of a rack of a back suspension bracket сориентируйте the top basic cup according to a photo. |
7. Establish on a rack a sealant and the top cup. |
8. Wrap a nut of fastening of the top cup and tighten with the set moment. Симите the adaptation compressing a spring. |
9. Establish a rack on the car. |
|
|
|