Toyota Camry

1996-2001 of release

Repair and car operation

Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
- 9. A running gear
   - 9.1.2. Technical characteristics
      9.1.3. The stabilizer of cross-section stability of a forward suspension bracket
      9.1.4. A rack of a forward suspension bracket
      9.1.5. A rack and a suspension bracket spring
      9.1.6. The suspension bracket lever
      9.1.7. Spherical support
      9.1.8. A rotary fist and a nave
      9.1.9. A nave and the bearing of a forward wheel
      9.1.10. The stabilizer and plugs of the stabilizer of a back suspension bracket
      9.1.11. A rack of a back suspension bracket
      9.1.12. A longitudinal bar
      9.1.13. Levers of a back suspension bracket
      9.1.14. A nave and the bearing of a back wheel
      9.1.15. An arm of a back suspension bracket
      9.1.16. Corners of installation of wheels
   + 9.2. A steering
   + 9.3. Semiaxes
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment

9.1.15. An arm of a back suspension bracket

THE GENERAL DATA

Arm of a back suspension bracket

1. An arm
2. The brake cylinder
3. A nave
4. A disk
5. A sealant
6. A drum
7. The gauge of speed (on cars equipped with ABS-system)

Removal

PERFORMANCE ORDER

1. Lift a back part of the car and establish on supports. Remove a back wheel.

2. Remove a drum or a brake disk in gathering with a support. On cars with back drum-type brakes disconnect a hydrodrive tube on the wheel cylinder. On cars with back disk brakes a hose from a support do not disconnect.

3. On cars with back disk brakes release and turn out a bolt of fastening of a flexible hose to a rack.

4. Remove a back nave with the bearing (subsection 9.1.14 see.).

5. On cars with back drum-type brakes remove a back brake in gathering with a board of a brake from a suspension bracket arm, without disconnecting a hose. On cars with back disk brakes remove a board of a brake with the mechanism of a lay brake. Fix the removed knots on a rack spring.

6. On the cars equipped with ABS-system, remove the gauge of speed.

7. Release bolts of fastening of an arm to a rack.

8. Turn away a bolt of fastening of the lever on an arm, remove a nut and washers then definitively turn out a bolt of fastening of an arm to a rack.

9. Supporting an arm, turn away the bolts of fastening of an arm released earlier to a rack and separate an arm from a rack.

Installation

PERFORMANCE ORDER

1. Check up a condition of plugs, presence on them of cracks and wear tracks. The worn out plugs vary in car-care centre.

2. Establish a suspension bracket arm on a rack arm, wrap bolts by hand.

3. Establish a bolt of fastening of the lever on an arm, a washer and screw a nut.

4. A jack raise a suspension bracket arm on the height corresponding to conditions of driving.

5. Tighten bolts of fastening of an arm of a suspension bracket to a rack with the set moment.

6. Attach a longitudinal bar and tighten a bolt with the set moment.

7. Tighten a bolt and a nut of fastening of the lever.

8. On cars with back drum-type brakes fix a hose on a rack.

9. On cars equipped with ABS-system establish the gauge of speed.

10. Establish a brake board, establish a nave and tighten bolts.

11. On cars with back drum-type brakes attach a tube to the wheel cylinder.

12. Establish a drum (or a disk) brakes.

13. Establish a wheel.

14. Remove air from a hydrodrive (subsection 10.11 see.).

15. Lower the car and tighten wheel nuts.