Toyota Camry

1996-2001 of release

Repair and car operation

Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
   - 3.3. A partition of engines
      3.3.1.2. 6-cylinder двухрядные engines
      3.3.2. Engine major repairs – broad-brush observations
      3.3.3. Diagnostics of the engine with the help вакууметра
      3.3.4. Engine major repairs – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. An engine partition
      3.3.8. A head of cylinders and valves
      3.3.9. The balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. A cranked shaft
      3.3.12. The block of cylinders
      3.3.13. Хонингование cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. A back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is more likely live, than it is dead …
      3.3.22. The analysis дымности an exhaust
      3.3.23. A gear belt for a mechanism drive timing
      3.3.24. Occurrence in deposit oil
      3.3.25. An engine overheat
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment

3.3.11. A cranked shaft

THE GENERAL DATA

Sequence of a tightening of bolts of covers of radical bearings (6-cylinder engines)

Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines)

Removal

PERFORMANCE ORDER

1. Before removing a cranked shaft, measure its free wheeling by means of the special device (drawing at the left) or with the help probeа near the persistent bearing (drawing on the right). If the backlash more than is required, examine half rings of the persistent bearing on deterioration presence if half rings are not worn out, it is necessary to establish new to adjust a backlash.

2. Covers of radical bearings should be numbered on increasing, from a forward cover to back if it not so, number them. Usually on covers there is an arrow who is directed towards a forward part of the engine. Loosen the bolts of covers in stages on a turn quarter at one time.

3. In six-cylinder engines bolts of covers (arrow) are located on each side the block of cylinders. Unscrew these bolts first of all in sequence of return that which is specified in drawing (see fig. the Sequence of a tightening of bolts of covers of radical bearings (6-cylinder engines)).

4. Then unscrew other bolts of covers in sequence of return sequence of a tightening (fig. Sequence of a tightening of lateral bolts of covers of radical bearings (6-cylinder engines) see).

5. Remove covers and get loose leaves of bearings.

6. Remove a cranked shaft.

Check

PERFORMANCE ORDER

1. Clear a cranked shaft solvent and dry up its compressed air.

2. Examine bearings of a cranked shaft on presence of wear tracks, scratches, corrosion or cracks.

3. Remove jags round lubricant apertures and clean apertures solvent.

4. Examine a cranked shaft on presence of cracks or other damages.

5. Measure diameters radical and шатунных bearings. To reveal конусность and ovality, measure diameter of each of bearings in several points. If necessary the cranked shaft needs to be processed in a specialised workshop.

6. Check up necks of epiploons of a cranked shaft on presence of wear tracks or damages. If epiploons have wiped flutes on necks new epiploons will pass oil.