Toyota Camry

1996-2001 of release

Repair and car operation


Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
   - 3.3. A partition of engines
      3.3.1.2. 6-cylinder двухрядные engines
      3.3.2. Engine major repairs – broad-brush observations
      3.3.3. Diagnostics of the engine with the help вакууметра
      3.3.4. Engine major repairs – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. An engine partition
      3.3.8. A head of cylinders and valves
      3.3.9. The balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. A cranked shaft
      3.3.12. The block of cylinders
      3.3.13. Хонингование cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. A back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is more likely live, than it is dead …
      3.3.22. The analysis дымности an exhaust
      3.3.23. A gear belt for a mechanism drive timing
      3.3.24. Occurrence in deposit oil
      3.3.25. An engine overheat
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4

3.3.14. Radical bearings and bearings of rods
THE GENERAL DATA

Causes of wear of bearings
1. Decrease in strength of metal; fragmentary scratches
2. It is incorrectly planted; the bright (polished) strips
3. It is scratched by a dirt; the dirt has eaten in a surface 		4. An oil lack; the top layer was wiped
5. Excessive deterioration; the top layer was wiped on all surface
6. The bearing is deformed; the top layer was wiped on a circle

In spite of the fact that at an engine partition old loose leaves of bearings are replaced on new, it is necessary to examine old loose leaves carefully. Loose leaf survey can establish the reason of its deterioration.

Damage of bearings occurs because of a lack of greasing, presence of a dirt and other alien particles, an engine and corrosion overload. In any case, the reason of damage of bearings is necessary for eliminating prior to the beginning of engine assemblage.

Selection of loose leaves

For correct selection of loose leaves be guided by size of a lubricant backlash by which it is possible to measure by means of a plastic measuring tape. At occurrence of any problems with selection of loose leaves address to experts.

Radical bearings

The sizes necessary for definition of a thickness of loose leaves of radical bearings (4-cylinder engines)
 

The sizes of radical bearings for 4-cylinder engines are beaten out on a joined surface of the oil pallet and on the block of cylinders (), the sizes of necks of radical bearings are beaten out on a counterbalance of a cranked shaft (). In 6-cylinder engines the sizes of bearings are beaten out on the block of cylinders over cranked shaft, and the sizes of necks of bearings are beaten out on the first counterbalance of a cranked shaft.

Having combined corresponding numbers on the block and on a cranked shaft, you receive the necessary size of the loose leaf for the four-cylinder engine. To pick up loose leaves for six-cylinder engines use the table.

The sum
Figure on the block of cylinders () plus figure on a cranked shaft ()
0 – 5
6 – 11
12 – 17
18 – 23
24 – 28
Use loose leaf N
3
4
5
6
7

Example: Figure on the block of cylinders 06 + figure on a cranked shaft 08 in the sum give 14 – use loose leaf N5.