Toyota Camry

1996-2001 of release

Repair and car operation



Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   + 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
   - 3.3. A partition of engines
      3.3.1.2. 6-cylinder двухрядные engines
      3.3.2. Engine major repairs – broad-brush observations
      3.3.3. Diagnostics of the engine with the help вакууметра
      3.3.4. Engine major repairs – alternatives
      3.3.5. Auxiliary elements of the engine
      3.3.6. Removal and engine installation
      3.3.7. An engine partition
      3.3.8. A head of cylinders and valves
      3.3.9. The balancing device (the 4-cylinder engine)
      3.3.10. Pistons and rods
      3.3.11. A cranked shaft
      3.3.12. The block of cylinders
      3.3.13. Хонингование cylinders
      3.3.14. Radical bearings and bearings of rods
      3.3.15. Measurement of size of a free wheeling of the balancing device
      3.3.16. Piston rings
      3.3.17. Radical bearings of a cranked shaft
      3.3.18. A back epiploon of a cranked shaft
      3.3.19. Shatunnye bearings
      3.3.20. Installation of the balancing device of the engine
      3.3.21. It is more likely live, than it is dead …
      3.3.22. The analysis дымности an exhaust
      3.3.23. A gear belt for a mechanism drive timing
      3.3.24. Occurrence in deposit oil
      3.3.25. An engine overheat
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4

3.3.19. Shatunnye bearings

Check of a lubricant backlash шатунных bearings

Arrangement of trailer backlashes of piston rings (the 4-cylinder engine)

1. Top компрессионное a ring
2. Deepening (it is directed towards a forward part of the engine)
3. Bottom маслосъемное a ring
4. Bottom компрессионное a ring
5. A broad ring
6. Top маслосъемное a ring

Arrangement of trailer backlashes of piston rings (the 6-cylinder engine)

1. The piston of the right number
2. Bottom маслосъемное a ring
3. A label directed towards a forward part of the engine
4. A label directed towards a forward part of the engine
5. Top маслосъемное a ring
6. Top компрессионное a ring
7. A broad ring
8. Bottom компрессионное a ring

Arrangement trailer ззоров rings of the piston of the left number identically.

PERFORMANCE ORDER
1. Clean the top loose leaf of the bearing of a rod and establish it on a rod. Lubricant apertures of a rod and the loose leaf should be combined.
2. Clean the second loose leaf and establish it in a rod cover.
3. Arrange trailer backlashes of piston rings as is shown in fig. the Arrangement of trailer backlashes of piston rings (the 4-cylinder engine) and on fig. the Arrangement of trailer backlashes of piston rings (the 6-cylinder engine).
4. Grease pistons and rings and compress piston rings by means of the compressor of piston rings.
5. Turn a cranked shaft so that шатунный the bearing of the first cylinder was in the family way the bottom dead point, and grease cylinder walls.
6. Check up, that the mark from above the piston has been turned forward.
7. Press on the piston and establish it in the cylinder.
8. Put plastic pieces on each of bearings of rods in parallel an axis of a cranked shaft.
9. Establish covers шатунных bearings (labels on covers should be directed aside газораспределительного a belt). Tighten bolts of covers according to the instructions resulted in technical characteristics (subsection 3.3.1.1 see., subsection 3.3.1.2.).
10. Compare width of the crushed film to a special scale.
11. If backlash size do not correspond demanded, possibly, loose leaves of the wrong size are established.

Definitive installation of pistons and rods

PERFORMANCE ORDER
1. Remove all traces of plastic. Check up, that the surface of loose leaves was absolutely pure, and grease with their engine oil.
2. Establish a rod on a shaft neck, establish a cover of a rod and tighten nuts till the demanded moment of an inhaling. Installation of other rods is spent similarly.
3. After installation of all rods turn a cranked shaft some times and check up ease of a course.
4. Check up axial люфт rods.