Toyota Camry

1996-2001 of release

Repair and car operation



Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   - 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
      3.2.2. Compression check
      3.2.3. The top dead point (ВМТ) piston N1
      3.2.4. Covers of heads of cylinders
      3.2.5. An inlet collector
      3.2.6. Final collectors
      3.2.7. A gazoraspredelitelnyj belt and asterisks
      3.2.8. A forward epiploon of a cranked shaft
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and lifts of valves
      3.2.11. Heads of cylinders
      3.2.12. The oil pallet
      3.2.13. The oil pump
      3.2.14. The Flywheel / a leading disk
      3.2.15. A back epiploon of a cranked shaft
      3.2.16. Engine fastenings
   + 3.3. A partition of engines
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4

3.2.7. A gazoraspredelitelnyj belt and asterisks
THE GENERAL DATA

Gazoraspredelitelnyj belt

1. A lining
2. A gazoraspredelitelnyj belt
3. A directing disk of a belt
4. An arm
5. A lining
6. A protective casing of wires
7. Intermediate pulley N1
8. A cover
9. A plate
10. Натяжитель a belt
11. An asterisk of a cranked shaft
12. A washer
13. Intermediate pulley N2
14. An asterisk of the left camshaft
15. An asterisk of the right camshaft
16. A pulley of a cranked shaft
17. The bottom cover of a belt
18. The right assembly arm of the engine
19. The top cover of a belt

Removal

PERFORMANCE ORDER
1. Disconnect a wire of the minus plug of the accumulator.
2. Remove a broad tank of system of cooling and a tank windscreen a windshield.
3. Remove приводные belts of the generator and the pump of system of strengthening of a steering.
4. Loosen the bolts of the right forward wheel. Lift and fix a forward part of the car. Remove a wheel. Remove isolation of an arch of a wheel.
5. Establish the cylinder of the first piston in the top dead point.
6. Unscrew two through bolts () and remove the draught regulating displacement of the engine () and a draught arm.
7. Remove spark plugs.

8. Remove the top cover газораспределительного a belt and a lining.

9. If you are going to reuse газораспределительный a belt, make on it adjusting labels.

10. Check up синхронизационные labels of asterisks of camshafts. Labels on asterisks of shaft should be combined with labels on a back cover of a belt.
11. Unscrew two bolts (arrow) and remove натяжитель a belt.
12. Loosen the a tension of a belt also remove a belt.
13. To remove a camshaft asterisk, uncover heads and stop a shaft a wrench (marksman). Braid a bolt of an asterisk and remove an asterisk.
14. Remove the top intermediate pulley.
15. Unscrew a bolt of a pulley of a cranked shaft, preliminary having stopped a flywheel.
16. Check up синхронизационные labels and remove a pulley.
17. Remove the bottom cover of a belt and a lining.
18. Remove directing disk of a belt.
19. If you are going to reuse a belt, make an adjusting label on a belt opposite to an aperture in an asterisk of a cranked shaft. Remove a belt.

Check

PERFORMANCE ORDER
1. Check up a belt (subsection 3.1.7 see.).
2. Check up, whether proceeds натяжитель a belt, if necessary replace натяжитель.
3. Measure an acting part of a rod натяжителя. If the received size does not correspond to technical requirements, replace натяжитель.

Installation

PERFORMANCE ORDER
1. Carefully clean a forward part of the engine.
2. Establish an asterisk of a cranked shaft (if you removed it) and combine a label синхронизационной asterisks with a label on the block of cylinders () and establish an asterisk clamp ().
3. Grease the bottom intermediate rod with hermetic, establish a pulley and tighten a bolt till the demanded moment of an inhaling.
4. Put on a belt, using adjusting labels.
5. Put on directing disk of a belt and the bottom cover of a belt.
6. Establish a pulley of a cranked shaft and tighten a pulley bolt.
7. Establish the top intermediate pulley and tighten an assembly bolt.
8. Establish asterisks of camshafts. The flange of a forward asterisk should be directed outside, and a flange of a back asterisk inside. Check up, that синхронизационные labels on asterisks and on a back cover of a belt have been combined. Tighten bolts of asterisks till the demanded moment of an inhaling.
9. Put on a belt asterisks of camshafts, using adjusting labels.
10. By means of a vice, press a rod натяжителя. Insert штопорный a pin in diameter of 1,27 mm into casing and rod apertures натяжителя.
11. Establish натяжитель and tighten its bolts. Get the lock probe of a rod.
12. Turn a cranked shaft clockwise on two complete revolutions. Check up синхронизационные labels.
13. Establish the remained details.