Toyota Camry

1996-2001 of release

Repair and car operation


Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
+ 2. Maintenance service
- 3. Engines
   + 3.1.2. Compression check
   - 3.2. 6-cylinder двухрядные engines V6 of 3,0 l
      3.2.2. Compression check
      3.2.3. The top dead point (ВМТ) piston N1
      3.2.4. Covers of heads of cylinders
      3.2.5. An inlet collector
      3.2.6. Final collectors
      3.2.7. A gazoraspredelitelnyj belt and asterisks
      3.2.8. A forward epiploon of a cranked shaft
      3.2.9. Epiploons of camshafts
      3.2.10. Camshafts and lifts of valves
      3.2.11. Heads of cylinders
      3.2.12. The oil pallet
      3.2.13. The oil pump
      3.2.14. The Flywheel / a leading disk
      3.2.15. A back epiploon of a cranked shaft
      3.2.16. Engine fastenings
   + 3.3. A partition of engines
   + 3.4. An engine electric equipment
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment


75acfaa4

3.2.10. Camshafts and lifts of valves
THE GENERAL DATA

Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the right head)

Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the left head)

Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the right head)

Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the left head)

Removal

PERFORMANCE ORDER
1. Establish the first piston in ВМТ. Remove covers of heads, газораспределительный a belt and a camshaft asterisk.
2. Check up, that синхронизационные labels on gear wheels of shaft have been combined.
3. Stop an auxiliary gear wheel of a shaft of final valves, having twisted a bolt in apertures of auxiliary and basic gear wheels.
4. Loosen the bolts of covers of bearings of a shaft of inlet valves in sequence of return sequence of their tightening (fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the left head) see. Remove covers of bearings and get a shaft.
5. Loosen the bolts of covers of bearings of a shaft of final valves in sequence of return sequence of their tightening (fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the left head) see). Remove covers and get a shaft.
6. Similarly remove shaft of other head.
7. Combine covers of bearings in correct sequence.
8. To disassemble a gear wheel of a shaft of final valves, fix a shaft in a vice. By means of a special key ослабьте pressure upon a boat twisted in gear wheels, also unscrew it.
9. Remove a lock ring of an auxiliary gear wheel.
10. Remove an auxiliary gear wheel (3), a spring (2) and washers (1).

Check

Cм. Subsection 3.1.10.

Installation

PERFORMANCE ORDER
1. Establish an auxiliary gear wheel and its elements.
2. Fix a shaft in a vice and again twist a bolt in apertures of gear wheels of a shaft. Grease with universal greasing lifts of valves (if you removed them) and establish them in corresponding nests.
3. Grease with special greasing cams and necks of bearings of a shaft of final valves, and establish a shaft in a head. Labels on a gear wheel should be directed towards a shaft of final valves (in drawing on the right – the right head, at the left – left).
4. Put hermetic on external parts of a joined surface of a cover of the first bearing (are marked by shading).
5. Establish covers of bearings as numbering. Arrows on covers should be directed aside газораспределительного a belt (in drawing on the right – the right head, at the left – left).
6. Tighten bolts of covers till the demanded moment of an inhaling. Tighten bolts in the specified sequence on the one fourth turn at one time (fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of final valves (the left head) see).
7. Establish a new epiploon of a shaft.
8. Grease with special greasing cams and necks of bearings of a shaft of inlet valves.
9. Establish a shaft in a head, having combined labels on gear wheels of shaft.
10. Establish covers of bearings as numbering. Arrows on covers should be directed aside газораспределительного a belt (in drawing on the right – the right head, at the left – left).
11. Tighten bolts of covers till the demanded moment of an inhaling. Tighten bolts in the specified sequence on the one fourth turn at one time (fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the right head), fig. Sequence of a tightening of bolts of covers of bearings of a shaft of inlet valves (the left head) see).
12. Unscrew stopping bolt from gear wheels of a shaft of inlet valves.
13. Establish asterisks of shaft and газораспределительный a belt.
14. Establish the remained details.