Toyota Camry

1996-2001 of release

Repair and car operation

3.1.11. A head of cylinders

THE GENERAL DATA

Head of cylinders of the engine 5S-FE

1. The system valve recycling Exhaust gases and the vacuum converter 2. A lining 3. A lining 4. A throttle 5. Демпфер pulsations in fuel system 6. A fuel hose 7. A lining 8. An inlet collector 9. A hose of return of fuel 10. A tube of giving of fuel 11. A sealing ring 11а Izoljatsionnaja the plug 12. An injector 13. An insulator 14. The plug 15. The valve 16. A cover of a head of cylinders 17. A clamp 18. An adjusting lining 19. The isolating plug 20. An epiploon 21. The valve 22. A spark plug 23. The valve lift 24. Clamps 25. A spring plate 26. A valve spring 27. A spring saddle 28. A lock ring 29. The directing plug of the valve 30. A camshaft of final valves 31. A hook for an engine raising 32. A branch pipe of system of cooling

33. Prorolling 34. The gauge of pressure of oil 35. A perepusknaja tube of system of cooling 36. A teploizolirujushchy guard of an oil radiator 37. A teploizolirujushchy guard of a final collector 38. Кронштей a final collector 39. Кронштей a final collector 40. A final collector 41. A lining 42. A sealing ring 43. A lining 44. A head of cylinders 45. A hook for an engine raising 46. Grounding contact 47. A generator arm 48. A lining of a head of cylinders 49. A cover газораспределительного a belt 50. A spring of a gear wheel of a camshaft 51. A lock ring 52. A washer 53. An epiploon 54. An additional gear wheel of a camshaft 55. A camshaft of inlet valves 56. A cover of the first bearing of a shaft 57. A lining 58. Fastenings of an inlet collector 59. An air tube 60. A lining 61. A vacuum tube 62. The vacuum valve of system recycling

Removal

Sequence of a tightening of bolts of a head of cylinders

PERFORMANCE ORDER

1. Disconnect a wire of the minus plug of the accumulator. 2. Merge cooling liquid from картера the engine and from a radiator. 3. Merge engine oil and remove the oil filter. 4. Remove a throttle, fuel injectors and a fuel highway. 5. Remove an inlet collector. 6. Remove a final collector. 7. Remove газораспределительный a belt, an asterisk of a camshaft and the top intermediate pulley. 8. Remove the top section of a back cover газораспределительного a belt. 9. Remove camshafts and lifts of valves. 10. Remove the generator and the ignition distributor. 11. Unscrew bolts of the pump of the amplifier of a steering. Shift the pump aside, without disconnecting from it hoses. 12. Disconnect all wires, tubes, hoses and the ropes fixed on a head of cylinders. 13. Loosen the also unscrew head bolts in sequence of return that which is specified in drawing Sequence of a tightening of bolts of a head of cylinders. Weaken bolts on a turn quarter at one time. 14. Remove a head of cylinders.

Installation

PERFORMANCE ORDER

1. Carefully clean and wipe acetone joined surfaces of a head and the block of cylinders. If surfaces are scratched or damaged otherwise they are necessary for processing in a specialised workshop. 2. By means of a suitable tap clean carvings in the block of cylinders. By means of a suitable die clean bolts of a head of cylinders. 3. Establish a new lining of a head and establish a head. 4. Grease bolts with pure engine oil. 5. Insert bolts and tighten them till the demanded moment of an inhaling in sequence specified on drawing Sequence of a tightening of bolts of a head of cylinders. 6. Establish the remained details.