Toyota Camry
+ 1. The maintenance instruction
+ 1.2. The information before car driving
+ 1.3. Independent maintenance service
+ 1.4. Technical characteristics
+ 1.5. Some councils at car purchase
- 2. Maintenance service
2.2. The schedule of servicing Toyota Camry/Avalon
2.3. Primary and secondary checks
2.4. Check of level of oil and liquids
2.5. Check of a condition of tyres and pressure in tyres
2.6. Check of level of a liquid of system of hydrostrengthening of a steering
2.7. Check of level of liquid automatic gearbox
2.8. Replacement of engine oil and the oil filter
2.9. Survey and replacement of brushes of screen wipers
2.10. Check, servicing and accumulator gymnastics
2.11. Check, adjustment of a tension and replacement drive a belt
2.12. Check and replacement of hoses in an impellent compartment
2.13. Check of system of cooling
+ 2.14. Shift of wheels
2.15. Check of brake system
2.16. Replacement of the air filter
2.17. Power supply system check
2.18. Check of level of a liquid of differential (automatic gearbox)
2.19. Check of level of oil manual transmission
2.20. Steering and suspension bracket check
2.21. Check of covers of semiaxes
2.22. Check of final system
2.23. Height and a free wheeling of pedals of coupling and a brake
2.24. Replacement of the fuel filter
2.25. Replacement of a cooling liquid and washing of system of cooling
2.26. Check of the system, supervising allocation of steams of fuel
2.27. Replacement of liquid automatic gearbox
2.28. Replacement of oil manual transmission
2.29. Check of fastenings of a body
2.30. Check and replacement of spark plugs
2.31. Check and replacement of wires of spark plugs
2.32. Check and adjustment of backlashes of valves
2.33. Replacement of a lining of a cover of a jellied mouth of a fuel tank
2.34. Check and replacement of the valve of ventilation картера
+ 3. Engines
+ 4. Cooling system
+ 5. Heating and ventilation
+ 6. Fuel system
+ 7. An exhaust system
+ 8. Transmission
+ 9. A running gear
+ 10. Brake system
+ 11. A body
+ 12. An electric equipment
|
Check
Examine приводные belts on all length from both parties on presence of cracks or wear tracks.
Deterioration клинового a belt
|
|
1. Deterioration of a lateral surface
2. Strong истирание surfaces
3. Cracks
4. Stratification
5. The polished surface
6. Pollution by oil
7. Rupture |
Deterioration of a ridge belt
|
|
1. Admissible deterioration
2. Cross-section cracks on belt edges
3. Inadmissible deterioration
4. There are no adjoining sites of edges of a belt in length more than 1 sm
5. The cracks parallel to edges of a belt |
| PERFORMANCE ORDER |
| Measure a tension of belts by means of special measuring tools and compare the obtained data to technical characteristics. If you do not have special tool, check up a tension, having pressed on a belt in the middle between two pulleys and having measured a belt deviation. The belt should deviate on 6 mm if the distance centre to centre pulleys makes 18–28 the Belt see should deviate on 12 mm if the distance centre to centre pulleys 30–40 see |
|
Measurement of a deviation of a belt by means of a ruler
|
|
1. A belt deviation
2. Check up, that the ruler was perpendicular рейке
3. Рейка
4. A ruler |
Tension adjustment
| PERFORMANCE ORDER |
|
1. For tension adjustment drive the generator and the compressor, ослабьте шарнирный a bolt () the generator in the left forward corner of the block of cylinders. Loosen the a lock bolt also turn an adjusting bolt () clockwise to pull a belt or counter-clockwise, to weaken. Measure a belt tension. If necessary spend repeated adjustment. |
| 2. For tension adjustment drive a belt of the pump of system of hydrostrengthening of a steering, ослабьте an adjusting bolt also turn the pump towards the engine or on the contrary to weaken or increase a belt tension accordingly. |
|
Replacement
| PERFORMANCE ORDER |
| Loosen the a tension drive a belt also remove it from pulleys. If one belt demands replacement, it is recommended to replace other belts also. |
|
|
|
